Civil Engineering
Distribution of Stresses in Soil - 3 PDH
This course covers the analysis of stress conditions at a point, stresses beneath structures and embankments, and empirical methods for estimating loads on buried pipes, conduits, shafts, and tunnels.
Domestic Wastewater Treatment - 3 PDH
This course will introduce you to the basics of domestic wastewater treatment. You will learn about preliminary measures, pretreatment, primary, secondary and advanced treatment processes, and sludge treatment and disposal. Approximate performance data …
Retaining Walls And Excavation Support Systems - 3 PDH
Retaining walls must be designed so that foundation pressures do not exceed allowable bearing pressures, wall settlements are tolerable, safety factors against sliding and overturning are adequate, and the wall possesses adequate structural strength. …
Marine Fueling Facilities - 3 PDH
This course provides an introduction to the design of marine applications of petroleum fueling facilities. Design of marine fuel receiving and dispensing facilities for the purpose of receiving fuel and/or loading fuel aboard ships, barges and boats for …
Small Flow Waste Treatment Systems - 3 PDH
This course will introduce you to small flow waste treatment systems such as septic tanks, waterless toilets, filtration and reuse systems, Imhoff tanks, and packaged treatment plants. You will learn about subsurface absorption and how to conduct …
Recycling Construction and Demolition Waste - 3 PDH
There is a significant amount of construction and demolition (C&D) waste developed due to construction activities and structure demolition, for example, at some installations, construction and demolition waste accounts for up to 80 percent of the solid …
Dam Arch Construction - 3 PDH
This course will introduce you to the construction of concrete arch dams. The design and analysis of any dam assumes that the construction will provide a suitable foundation and uniform quality of concrete. The design also depends on the construction to …
High Temperature Water Heating Plants - 5 PDH
This course will introduce you to systems, equipment and design guidelines for high temperature water (HTW) heating plants. HTW systems are used for heating multi-building facilities such as campuses and industrial and commercial activities. The advantage …
Deep Foundations - 3 PDH
This course will provide you with an introduction to deep foundations. A deep foundation derives its support from competent strata at significant depths below the surface or, alternatively, has a depth to diameter ratio greater than 4. A deep foundation …
Cathodic Protection Maintenance - 3 PDH
This course will provide you with an introduction to the methods, equipment and practices for inspection and maintenance of cathodic protection systems. Both galvanic (sacrificial anode) and impressed current systems are discussed.
Primary Wastewater Treatment - 3 PDH
Wastewater treatment is usually characterized as consisting of four sequential processes: preliminary, primary, secondary and tertiary treatment. This course will introduce you to processes and equipment for primary treatment of wastewater. You will be …
Architectural Design: Golf Clubhouses - 3 PDH
This course will introduce you to the fundamentals of golf clubhouse design. You will learn about the fundamentals of site and building design, functional area criteria, space allocations and illustrative designs for small, medium and large clubhouses. …
Structural Aluminum Performance-Based Design - 4 PDH
The core concept discussed in this document presents a broad overview of Performance-Based Structural Aluminum design employing various aluminum grades and aluminum alloys.
Fuel Cells Green Power - 3 PDH
Fuel cells are not just laboratory curiosities. While there is much work that needs to be done to optimize the fuel cell system (remember, the gasoline internal combustion engine is nearly 120 years old and still being improved), hydrogen fuel cell …
Domestic Wastewater Treatment: EPA Overview - 3 PDH
The 1972 legislation known as the Clean Water Act set secondary treatment as the required level of treatment to be provided by domestic wastewater treatment plants in the United States. In this course you can learn about the basic processes used in …
Hydraulic Jumps and Non-Uniform Open Channel Flow - 2 PDH
Many examples of open channel flow can be approximated as uniform flow allowing the Manning equation to be used. Non-uniform flow calculations are needed, however, in some open channel flow situations, where the flow is clearly non-uniform. The concepts …
Basics of Passive Solar Heating - 4 PDH
The principles of passive solar heating, such as basic types of systems, their description, and the components making up any passive system are presented in this course. Sources of data for heating requirements and available solar radiation throughout the …
Biofuels Basics - 3 PDH
Biofuels is one of the Administration’s near-term strategies to address energy security and climate change. In his 2006 State of the Union Address, President Bush declared that America “is addicted to oil” and rolled out the Advanced Energy Initiative …
Sharp-Crested Weirs: Open Channel Flow Measurement - 2 PDH
A weir is basically an obstruction in an open channel flow path. Weirs are commonly used for measurement of open channel flow rate. A weir functions by causing water to rise above the obstruction in order to flow over it. The height of water above the …
Uniform Open Channel Flow and The Manning Equation -2 PDH
Flow of a liquid may take place either as open channel flow or pressure flow. Pressure flow takes place in a closed conduit such as a pipe, and pressure is the primary driving force for the flow. For open channel flow, on the other hand the flowing liquid …